Plumbing Basics: What You Need for Installing a Bathtub
Plumbing Basics: What You Need for Installing a Bathtub
Blog Article
They are making a number of good annotation regarding A Step-by-Step Guide to Installing a Bathtub in general in this post down the page.
Setting up a bath tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately difficult job. If the old bathtub is readily accessible, the project can move immediately; if you need to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the task is much harder. In either situation, the task is within a house handyman's skills, although you will certainly require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually qualified on your own for the work as well as are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed task, it is much better to consider using one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This post will certainly help you install a new bath tub in your bathroom if you have actually already acquired a new tub as well as don't need to change the plan of your previous water pipes.
Your tools and product list should comprise the following:
Preparing for the Installment
Firstly, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipes. When the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bath tub till the spirit level reviews level.
To install faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipe by making a compression join; then do the very same for the other tap.
Switch on the water and also examine all joints and also new pipework for leaks and also tighten them if required. Fill up the bath tub and also examine the overflow outlet and also the regular outlet for leaks.
Lastly, fix the bath paneling as described in the maker's user's manual. Tiling and sealing around the bathtub ought to wait until the bath tub has been made use of at the very least when as this will certainly resolve it into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and the sink. Protect the tap in position with the supplier given backnut. When the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture an inflexible seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, causing problems with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub is in usage. The sealer can fracture relatively early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the floor tiles using water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very drawn to How to Install a Bathtub Yourself and I am praying you appreciated the entire blog posting. Do you know someone else who is sincerely interested in Installing A Bathtub? Do not hesitate to share it. Thank you for your time spent reading it.
Services Report this page